please dont rip this site

Language Pcl LJ1912.ASC

USING  EDGE WEDGE WITH PIE CHARTS

    
     The Edge Wedge ( EW ) command defines and edges a wedge
     using the current pen, line type and attributes to
     outline a wedge. When the command is completed the
     original pen location and up/down status of the pen are
     restored.  For more information see the PCL 5 Printer
     Language Technical Reference Manual.
     
     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT.
     
     
     EcE                           Resets the printer.
     
     Ec%0B                         Enters HP-GL/2 mode.
     
     IN;                           Initializes HP-GL/2 mode.
     
     SP1;                          Selects pen number 1,
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.
     
     SC-3000,3000,-2000,2000,1;    Enters the scaling mode,
                                   specifying P1 as (-3000,-
                                   2000) and P2 as
                                   (3000),2000), using
                                   isotropic scaling.
                                   (Isotropic scaling means
                                   the X and Y units are the
                                   same size.)
     
     PA0,0;                        Specifies absolute
                                   plotting, then moves to
                                   (0,0).
     
     EW-1000,90,180;               Draws a wedge section
                                   with a radius of 1000
                                   user-units, a start angle
                                   of 90 degrees and a sweep
                                   angle of 180 degrees. The
                                   minus sign before the
                                   radius (-1000) sets the
                                   zero-degree reference
                                   point to the left side of
                                   the drawing.
     
     EW-1000,330,120;              Using the same center
                                   point and zero-degree
                                   reference point this
                                   draws a second wedge
                                   section outline starting
                                   at 330 degrees and sweeps
                                   120 degrees.
     
     PR-60,110;                    Moves the cursor 60 user-
                                   units to the left and 110
                                   user-units up.
     
     EW-1000,270,60;               From the new center point
                                   location, draws a wedge
                                   using a negative zero-
                                   reference point, starting
                                   at 270 degrees and
                                   sweeping for 60 degrees.
     
     Ec%0A                         Enters the PCL mode.
     
     EcE                           Sends a reset to end the
                                   job and eject the page.
     
            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.
     
     


file: /Techref/language/pcl/lj1912.asc, 3KB, , updated: 1993/11/15 16:17, local time: 2024/12/2 12:55,
TOP NEW HELP FIND: 
18.97.9.168:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.org/techref/language/pcl/lj1912.asc"> language pcl lj1912</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .