| You have completed your set of glyphs but something is wrong, It is flat
on a side that should have curve to it. Well, I hope this piece will help
you to put the curve where you want it. Below, I have tried to show how you can Add or Remove both points and curves, You will have to do both to get the look that you want for your glyph. If you look, you will see that I did construct an alphabet with Softy, Don't know if it could be made into a saleable font, but it can be fun. You can always add your signature to a font, That could be useful no? |
 Here, I have a glyph that I had made
for the period. I didn't care that it was square, I just wanted to see what
points were all about so I took the smallest and easiest to repair or replace
if I did something wrong. Here, You can see one of the points is highlighted
(the little black box) |
 On the TTF menu, you will find
POINTS Now, Here you can add a point or remove a point, add a curve
or remove a curve, the difference between the two points is that one looks
like a small box (for Streight Lines) and the other looks like a small circle
(for Curved Surfaces). I guess that makes it easy to see what you are pulling
on since the box is for streight lines and the circle is for curved lines. |
 I just put this in to show you, All
you do is to click and drag the point to where you want it. If you registered
Softy It says that you can use the key board to move the points one
pixel at a time, It does work but I find that draging works a little faster
for me. |
 Here I selected the Number four by double
clicking on it in the Display window on the extreme left and that entered
it into the edit window, you can now make changes to your glyph. You may
find something very simple like, the glyph is not centered in the box surrounding
it. In this case, you just select Center under Glyph on the
TTF Menu. It will center the glyph, Then select Update, That's it.
Now, just remember to save the font back to the drive and you would be done. |
 |
 This is the Number four after I had
pushed, pulled, added and removed points. Granted it is not a masterpiece,
but it shows you what you can do (the rest is patience). I could have altered
it to stand totally upright, but it was a sample of the way I write so I
didn't streighten it to much otherwise it would not be mine. |
 Now, Here is a sample of a glyph that
could be a problem. It is not properly located, It looks like it might be
in a smaller space than it should be, I will first try centering it and then
see if that will do it. If not, I would then move the crowfoot to allow it
to fit, them center it again |
 Having centered the glyph, I then went
on to Add/Remove points as I thought necessary and this is how it looks now.
I then Centered it again(It is easy to move the glyph while you are working
with the points, If you click off the point you activate the ability to shift
the glyph). Remember, I am not trying to make a perfect font here, This is
for me and you to get a better understanding of Softy. OK, done? Remember
UPDATE the glyph, and Save, else all is for naught. |
 This is what I was just saying, click
inside the glyph box but not on a point and this broken line box appears,
You can now click anywhere on the glyph and drag it to the place you want
it located. When you are satisfied, just click your mouse again and the glyph
is anchored and the box disappears. |
| The biggest thing here is to remember to Update and Save the font, Should you forget, then you will have to start again. I hope you find this informative and helpful. From here out, It is going to depend on you and the amount of patience you can muster. Most of all, Have fun, and enjoy yourself. |
| file: /Techref/member/softy-font/grumpy/points.htm, 5KB, , updated: 2003/6/4 12:09, local time: 2024/11/19 12:31,
13.59.188.225:LOG IN
|
| ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://massmind.org/techref/member/softy-font/grumpy/points.htm"> Adding and Removing Points with Softy Font Editor</A> |
| Did you find what you needed? |