please dont rip this site

Scenix Bargraph.src

; ******************************************************************************
;	Pulse Width Modulated 'Linear' LED Bar Graph Display  -  (c) 1998
;
;
;	Length: 87 bytes
;	Author:	Craig Webb
;	Written: 97/02/26
;
;	This program implements two virtual peripherals using interrupts.
;	It shows to read a potentiometer as an 8 bit value and pulse width
;	modulate a bar-graph of 16 LEDs arranged in a 4x4 matrix on port B
;	in order to provide a smooth 'sliding' signal effect by varying the
;	brightness of adjacent LEDs when the potentiometer 8 bit value lies
;	somewhere between them.
;	
;
;******************************************************************************
;
;******	Assembler directives
;
		DEVICE		pins18,pages1,banks8,stackx,optionx
		DEVICE		osc4mhz,turbo
		ID		'16 LEDs'
		RESET		Start			;set reset/boot address
;
;******************************* Program Variables ***************************
;
;******	Register definitions (bank 0)
;
		ORG	08h			;global variables 08-0Fh
reading		DS	1			;potentiometer reading
display		DS	1			;LED display output level
flags		DS	1			;program flags
;
; variables for LED interrupt routine
;
		ORG	10h			;bank 0 variables
mainbank	EQU	$
;
LED_bank	EQU	$			;(can be other than bank 0)
LED		DS	1			;holds which LED to light
cycle_count	DS	1			;pwm cycle count
pot_count	DS	1			;temporary pot timing count
clear_delay	DS	1			;delay period to clear cap.
sample_delay	DS	1			;delay period per sample
						; (reduces power consumption)
;
;******	Bit variable definitions
;
pot		EQU	RA.0			;potentiometer in RC (input)
triggered	EQU	flags.0			;status of pot. reading
clearing	EQU	flags.1			;hi while cap. is clearing
;
;******	Constants
;
sample_time	=	2			;time between pot. readings
clear_time	=	45			;delay value for clearing
						; the capacitor (>=2)
int_period	=	200			;interrupt period (based
						;          on RTCC counts)
IO_portA	=	00001111b		;Port A input/output setup
LEDs_off	=	0Fh			;RB value for LEDs=off
;
;************************* Interrupt Routines ****************************
;	
		ORG	0
;
;*****	Virtual Peripheral : Read potentiometer
;
; This routine reads the value of the potentiometer by clearing the
; capacitor in the RC timing circuit and then measuring the time it takes
; the capacitor to charge until the port input goes high. To avoid high
; current draws at low potentiometer values, the routine only resamples
; after (256*sample_time) interrupt cycles. The maximum potentiometer
; reading is 255.
;
;	Input variable(s) : none
;	Output variable(s) : reading
;	Variable(s) affected : pot_count, clear_delay, sample_delay
;	Flag(s) affected : clearing, triggered
;	Timing cycles (turbo) : 12-charging, 14-triggered, 14-clearing
;
		JNB	clearing,:charge	;are we clearing cap.?
		MOV	W,#11111111b		;get port mask (=done)
		DECSZ	clear_delay		;is count done?
		MOV	W,#11111110b		;no, get port mask (=clearing)
		TEST	clear_delay		;is count done?
		SNZ				;if not, skip ahead
		CLRB	clearing		;yes, reset clearing flag
		AND	W,#IO_portA		;get port setup byte
		MOV	!RA,W			;adjust pot port status
		CLR	pot_count		;clear timing count
		JMP	:done_pot		;jump past checking routine
:charge		JNB	pot,:adjust_count	;triggered yet?
		MOV	W,pot_count		;get timing count
		SB	triggered		;is this first trigger cycle?
		MOV	reading,W		;yes, store result
		SETB	triggered		;set trigger flag
:adjust_count	INCSZ	pot_count		;adjust reading counter
		JMP	:done_pot		;was counter at maximum?
		MOV	W,#255			;no, store max. value
		SB	triggered		;did we already get reading?
		MOV	reading,W		;no, so set it to max.
		SETB	triggered		; and flag that we got value
		DECSZ	sample_delay		;time for new sample?
		JMP	:done_pot		;if not, keep cycling
:trig		CLRB	triggered		;yes, reset trigger flag
		SETB	clearing		;set flag to clear cap.
		MOV	sample_delay,#sample_time	;load sample and
		MOV	clear_delay,#clear_time	; clear delay time counts
:done_pot					;end of pot. reading routine
;
;
;*****	Virtual Peripheral : LED driver
;
; This routine drives the LED bar-graph array, providing 16 levels
; of brightness to allow an output slide effect between adjacent LEDs
; It must be called fairly often, otherwise the pulsing effect will
; become noticeable.
;
;	Input variable(s) : display
;	Output variable(s) : none
;	Variable(s) affected : cycle_count, LED
;	Timing cycles (turbo) : 21
;
;next instruction needed only if multiple variable banks are used
;
		MOV	W,<>display		;get input (nibble-swapped)
		AND	W,#0Fh			;keep high 4 bits (which LED)
		MOV	LED,W			;save it
		MOV	W,display		;get input level again
		AND	W,#00001111b		;keep lower 4 bits for PWM
		MOV	W,cycle_count-W		;calculate which LED to have on
:zero_point	SZ				;adjust zero baseline up one*
		SC				;next one up? If not skip ahead
		INC	LED			;yes, increment to next LED
		MOV	W,LED			;get LED number
		CALL	LED_Table		;fetch LED value
		MOV	RB,W			;light LED
		INC	cycle_count		;adjust PWM cycle
		SNB	cycle_count.4		;time to reset (16 cycles)?
		CLR	cycle_count		;yes, start new cycle
;
;*this instruction shifts the whole display range up by one, thus making the
;  first LED dimly lit on a reading of 0, and the last lit fully on a reading
;  of 255. If it's preferable that all LEDs be off on a reading of 0, this
;  instruction may be removed or commented out.
;
;
		MOV	W,#-int_period		;interrupt again after
		RETIW				;   'int_period' RTCC counts
;
;******************************* Subroutines *********************************
;	
;
;*****	Subroutine : LED_Table
;
; This is a look-up table that returns the output port value to light the LED
; contained in the W register. If W holds 0, then all LEDs are turned off.
;	
LED_Table	ADD	PCL,W			;get RB value for LED1-16
		RETW	0Fh			;LEDs all off
		RETW	1Eh			;LED1
		RETW	2Eh			;LED2
		RETW	4Eh			;LED3
		RETW	8Eh			;LED4
		RETW	1Dh			;LED5
		RETW	2Dh			;LED6
		RETW	4Dh			;LED7
		RETW	8Dh			;LED8
		RETW	1Bh			;LED9
		RETW	2Bh			;LED10
		RETW	4Bh			;LED11
		RETW	8Bh			;LED12
		RETW	17h			;LED13
		RETW	27h			;LED14
		RETW	47h			;LED15
		RETW	87h			;LED16
;
;
;********************************* Main Program *******************************
;
;*****	Initialization routine
;
Start		CLR	RA			;clear port A
		MOV	!RA,#IO_portA		;set up port A
		MOV	RB,#LEDs_off		;set all LEDs off
		MOV	!RB,#0			;configure port B as outputs
		CLR	FSR			;reset all ram starting at 08h
:zero_ram	SB	FSR.4			;are we on low half of bank?
		SETB	FSR.3			;If so, don't touch regs 0-7
		CLR	IND			;clear using indirect addressing
		IJNZ	FSR,:zero_ram		;repeat until done
		MOV	!OPTION,#10001000b	;enable interrupt on rtcc=xtal/1
		MOV	sample_delay,#sample_time	;load sampling period
;
;***** Main program loop
;
Mainloop
;
		MOV	display,reading		;copy pot. to LED ouput
;
;		<program code goes here>
;
		JMP	Mainloop		;keep looping
;
		END


file: /Techref/scenix/bargraph.src, 6KB, , updated: 1999/6/14 10:18, local time: 2024/12/2 12:45,
TOP NEW HELP FIND: 
18.97.9.168:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.org/techref/scenix/bargraph.src"> scenix bargraph</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .