please dont rip this site

Scenix Lib IO Dev Stepper Stepper.src

;  Filename: 	STEPPER.SRC

; Author:	Stephen Holland
; Revision:	1.0
; Date:		July 24, 1998
; Part:		SX28AC rev. 2.5
; Freq:		50Mhz
; Compiled using Parallax SX-Key software v0.84
;    
;
;*************************************************************
; Device
;*************************************************************
		device	pins18,pages4,banks8,oschs
		device	turbo,stackx,optionx,carryx
		id	'STEPPER'
		reset	reset_entry

		freq	50_000_000

;*************************************************************
; Equates
;*************************************************************
step_out	=	rb
led_pin         =       ra.3

;*************************************************************
; Variables
;*************************************************************
			org	8

temp		ds	1
counter		ds	1

;*************************************************************
; Bank 0 variables
;*************************************************************
		org	10h	

timers		=	$		;Timer variables

timer_low	ds	1	
timer_mid	ds	1
timer_high	ds	1
timer_accl	ds	1
timer_accm	ds	1
timer_acch	ds	1
timer_flag	ds	1

;*************************************************************
; Bank 1 variables
;*************************************************************
		org	30h	

motors		=	$

step_con	ds	1
step_dividel	ds	1
step_divideh	ds	1

step_lo		ds	1
step_hi		ds	1

;*************************************************************
; Interrupt routine - virtual peripherals
;*************************************************************

		org	0
interrupt					;3 it takes 3 cycles to get an interrupt

;*************************************************************
; Timers
;*************************************************************
		bank	timers			;1 24-bit timer

		clc				;1	
		add	timer_accl,timer_low	;2
		sc				;1
		jmp	:timer_out
		setb	timer_flag.0		;1 ;834us delay timer
		add	timer_accm,timer_mid	;2
		sc				;1
		jmp	:timer_out
		setb	timer_flag.1		;1 ;213ms delay timer
		add	timer_acch,timer_high	;2	
		snc				;1
		setb	timer_flag.2		;1 ;54.6s delay timer

		movb	led_pin,timer_acch.1	;4 =10
:timer_out					;=7

;*************************************************************
; Stepper Motor
;
; This routine excites the stepper motor using half-step sequence. 
; The excitiation method can be changed by modifying the startstep
; lookuptable with the appropriate sequence of excite output.
;
; The stepper motor can be connected to portb via the following circuit:
;
;               ULN2003
;              __________                   To stepper
;     rb.0----|1       16|-------------------coil 1
;     rb.1----|2       15|-------------------coil 2
;     rb.2----|3       14|-------------------coil 3
;     rb.3----|4       13|-------------------coil 4
;            -|5       12|-
;            -|6       11|-
;            -|7       10|-
;        -----|8________9|---|<|-------------common
;        |               12V Zener |
;      -----                       |
;       ---                        ---- +12V
;        -
;
; The stepper is controlled via the step_con register. The motor can
; be single stepped by setting the step_con.0 bit and run continuously
; by setting the step_con.1 bit. The rotation rate is set by modifying 
; the step_lo and step_hi registers. To set the rotation rate, the
; following equation can be used:
;
; delay = desired rev per second/(RTCC*CLK^-1*steps)
; 	where:
;		CLK = SX clock frequency
;		steps = number of steps/rotation for stepper used
;			(ie. 360degrees/7.5degrees per step = 48)
;
; step_lo * step_hi = delay
;
;*************************************************************
stepper	
		bank	motors
		clc
		snb	step_con.1
		jmp	:run
		sb	step_con.0
		jmp	:stepper_out
						
:run		djnz	step_dividel,:stepper_out ;3,2	;64th time through?
		djnz	step_divideh,:stepper_out ;3,2	;127th time through?

		csae	counter,#endstep	;1 take new table value
		jmp	:continue1		;1 
		mov	counter,#startstep	;1 reload table-counter
:continue1	mov	w,counter		;1
		mov	m,#6			;1 set page
		iread				;1 get table_data
		mov	m,#$0f			;1
		mov	step_out,w		;1
		inc	counter			;1

		mov	step_dividel,step_lo
		mov	step_divideh,step_hi
		clrb	step_con.0
:stepper_out

;*************************************************************
; End of interrupt routine
;*************************************************************
interrupt_out	mov	w,#-163			;1	;interrupt every 163 clocks

		retiw				;3

;*************************************************************
; Reset entry
;*************************************************************

reset_entry	mov	m,#$0f
		mov	!ra,#%0100		;set ra data direction register
		mov	!rb,#%11110000		;set rb data direction register

		clr	fsr			;reset all ram banks
:loop		setb	fsr.4
		clr	ind
		ijnz	fsr,:loop

		bank	timers			;set defaults
		setb	timer_low.0

		bank	motors
		clr	step_con

		mov	!option,#%10011111	;enable rtcc interrupt

;*************************************************************
; Main 
;*************************************************************
main
		mov	temp,#6		;Single step the motor 6 times
main_loop

		bank	motors			
		setb	step_con.0

		bank	timers		;Delay for approx. 1 second between steps
		clrb	timer_flag.1
		jnb	timer_flag.1,$
		clrb	timer_flag.1
		jnb	timer_flag.1,$
		clrb	timer_flag.1
		jnb	timer_flag.1,$
		clrb	timer_flag.1
		jnb	timer_flag.1,$
		clrb	timer_flag.1
		jnb	timer_flag.1,$

		djnz	temp,main_loop

		bank	motors		;Set revolutions for approx. 1 rev/s
		mov	step_lo,#$ff
		mov	step_hi,#$19
		setb	step_con.1

		jmp	$

;*************************************************************
; Subroutines 
;*************************************************************
		org	$200









;*************************************************************
; Data
;*************************************************************

		org	$620

startstep	=	$
		dw	1	; 1
		dw	3	; 2
		dw	2	; 3
		dw	6	; 4
		dw	4	; 5
		dw	12	; 6
		dw	8	; 7
endstep		=	$
		dw	9	; 8





file: /Techref/scenix/lib/io/dev/stepper/STEPPER.SRC, 6KB, , updated: 2001/4/3 08:40, local time: 2024/12/2 12:42,
TOP NEW HELP FIND: 
18.97.9.168:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.org/techref/scenix/lib/io/dev/stepper/STEPPER.SRC"> scenix lib io dev stepper STEPPER</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .