; Pulse width capture test ; ; Board: SX Demo/Proto Board ; ; Three routines are tested - 8 bit, 16 bit, and 24 bit. The resolution ; is 4 cycles in every case. Testing is done manually in step mode. ; ; A routine is selected by three buttons at RB3, RB2, RB1: ; ; RB3=0 - 8-bit ; RB2=0 - 16-bit ; RB1=0 - 24-bit ; ; A pulse is generated manually by pressing a button at RB0. ; ; The pulse measurement code is based on Scott Dattalo's idea. ; ; May 10, 2001 ; by Nikolai Golovchenko DEVICE SX28L, OSCHS2, TURBO, STACKX, OPTIONX RESET start ORG $08 ;global bank pulse0 DS 1 ;LSB of the counter pulse1 DS 1 pulse2 DS 1 ;MSB ORG $10 ;bank0 ORG $30 ;bank1 ORG $50 ;bank2 ORG $70 ;bank3 ORG $90 ;bank4 ORG $B0 ;bank5 ORG $E0 ;bank6 ORG $F0 ;bank7 RA_DIR EQU %00000000 RB_DIR EQU %00001111 ;RB.0 .. RB.3 - button inputs RC_DIR EQU %00000000 ;input port pins but_8 EQU RB.3 but_16 EQU RB.2 but_24 EQU RB.1 pulse EQU RB.0 OPTION_INIT EQU $7F ;OPTION load value ;x--- ---- 0 = register 01h addresses w ;-x-- ---- 1 = RTCC roll-over interrupt is disabled ;--x- ---- 1 = RTCC increments upon transition on RTCC pin ;---x ---- 1 = RTCC increments on high-to-low transitions ;---- x--- 1 = Prescaler is assigned to WDT, and divide rate on ; RTCC is 1:1 ;---- -xxx 111 = Prescaler divider 1:128 (WDT) ;**************************************************************************** ; Start of program ;**************************************************************************** ORG $000 ;page 0 start ;init ports clr RA clr RB clr RC mov w, #RA_DIR mov !RA, w mov w, #RB_DIR mov !RB, w mov w, #RC_DIR mov !RC, w ;load option and make w addressable mov w, #OPTION_INIT mov !OPTION, w ;**************************************************************************** ; Main loop: ; 1) wait a transition in pulse from 0 to 1 ; 1) select the test routine ; 2) measure the pulse width ; 3) goto 1 ;**************************************************************************** loop ;wait the low to high transition snb pulse jmp $-1 sb pulse jmp $-1 ;select and run the test routine call select ;repeat jmp loop ;selection routine select sb but_8 jmp mpulse8 ;call pulse8 and return sb but_16 jmp mpulse16 ;call pulse16 and return sb but_24 jmp mpulse24 ;call pulse24 and return retp ;if nothing selected just return ;**************************************************************************** ; 8 bit pulse width measurement at 4 cycle resolution ; ; Return values at check points A and B (see below) will be: ; Check point: A B A B A B A B ... ; Counter value: 1 2 3 4 5 6 7 8 ... ; ; Size: 11 instruction words ;**************************************************************************** mpulse8 mov w, #1 ;init counter mov pulse0, w mov w, #2 ;init increment size mpulse8_loop sb pulse ;check input the first time (A) jmp mpulse8a ; if low, exit add pulse0, w ;increment counter by two nop ;wait a cycle to sample at an equal interval ;instead of nop we can restart the watchdog: ; clrwdt ;or check the counter overflow: ; sc snb pulse ;check input the second time (B) jmp mpulse8_loop ;here the pulse end was detected after the second input check - correct the ;counter clrb pulse0.0 mpulse8a ;here the pulse end was detected after the first input check - leave the counter ;unchanged; if we fall here from the second input check, don't change counter ;either. retp ;return ;**************************************************************************** ; 16 bit pulse width measurement at 4 cycle resolution ; ; Return values at check points A, B, and C (see below) will be: ; Check point: A B C A B C A B C A ... ; Counter value: 0 1 2 3 4 5 6 7 8 9 ... ; ; Size: 23 instruction words ;**************************************************************************** mpulse16 clr pulse0 ;clear LSB of the counter clr pulse1 ;clear MSB of the counter mov w, #3 ;init increment size mpulse16loop sb pulse ;check input the first time (A) jmp mpulse16a ; if low, exit add pulse0, w ;increment counter by three nop ;wait a cycle to sample at an equal interval ;instead of nop we can restart the watchdog: ; clrwdt ;or check the counter overflow: ; sb pulse1.7 - counter value is limited to 0..32770 ;or: sb pulse1.6 - counter value is limited to 0..16387 ;or: sb pulse1.5 - counter value is limited to 0..8197 ;or: sb pulse1.4 - counter value is limited to 0..4099 ; sb pulse ;check input the second time (B) jmp mpulse16b snc ;propagate carry to the higher byte inc pulse1 ; snb pulse ;check input the third time (C) jmp mpulse16loop ;here we construct the correction value in w according to the check point - ;A (w = 0), B (w = 2), or C (w = 1). Then counter is then corrected - ;pulse = pulse - w. ;point C entry xor w, #$03 ;3^3^2^3 = 1 clc ;clear carry to avoid following carry propagation ;point B entry mpulse16b xor w, #$02 ;3^2^3 = 2 snc ;propagate carry if we didn't finish the addition inc pulse1 ; ;point A entry mpulse16a xor w, #$03 ;3^3 = 0 ;correct counter sub pulse0, w sc dec pulse1 ;return retp ;**************************************************************************** ; 24 bit pulse width measurement at 4 cycle resolution ; ; Return values at check points A, B, C and D (see below) will be: ; Check point: A B C D A B C D A B C D A ... ; Counter value: 3 4 5 6 7 8 9 10 11 12 13 14 15 ... ; ; Size: 39 instruction words ;**************************************************************************** mpulse24 clr pulse0 ;clear LSB of the counter clr pulse1 ;clear middle byte of the counter clr pulse2 ;clear MSB of the counter mov w, #1 ;init increment size mpulse24loop sb pulse ;check input the first time (A) jmp mpulse24a ; if low, exit add pulse0, w ;increment counter by one nop ;wait a cycle to sample at an equal interval ;instead of nop we can restart the watchdog: ; clrwdt ;or check the counter overflow: ; sb pulse2.6 - counter value is limited to 0..2^24 ;or: sb pulse2.5 - counter value is limited to 0..2^23 ;or: sb pulse2.4 - counter value is limited to 0..2^22 ;etc... ; sb pulse ;check input the second time (B) jmp mpulse24b snc ;propagate carry to the higher byte add pulse1, w ; sb pulse ;check input the third time (C) jmp mpulse24c snc ;propagate carry to the higher byte add pulse2, w ; snb pulse ;check input the fourth time (D) jmp mpulse24loop ;here we construct the correction value in w according to the check point - ;A (w = 3), B (w = 0), C (w = 1), or D (w = 2). Then counter is then corrected - ;pulse = (pulse << 2) + w. ; ;for simplicity, the two lower bits can be shifted into pulse, but the bits ;should be reversed: ;A (w = 3), B (w = 0), C (w = 2), or D (w = 1) ;point D entry xor w, #$03 ;1^3^2^3^2 = 1 clc ;clear carry to avoid following carry propagation ;point C entry mpulse24c xor w, #$02 ;1^2^3^2 = 2 snc ;propagate carry if we didn't finish the addition inc pulse2 ; clc ;clear carry to avoid following carry propagation ;point B entry mpulse24b xor w, #$03 ;1^3^2 = 0 snc ;propagate carry if we didn't finish the addition incsz pulse1 ; dec pulse2 ; inc pulse2 ; ;point A entry mpulse24a xor w, #$02 ;1^2 = 3 ;correct counter rr WREG rl pulse0 rl pulse1 rl pulse2 rr WREG rl pulse0 rl pulse1 rl pulse2 ;return retp ;**************************************************************************** ORG $200 ;page 1 ORG $400 ;page 2 ORG $600 ;page 3
file: /Techref/scenix/lib/io/osi1/sensor/plusewidth-ng.htm, 8KB, , updated: 2001/5/19 20:23, local time: 2024/12/23 21:21,
18.217.104.36:LOG IN
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://massmind.org/techref/scenix/lib/io/osi1/sensor/plusewidth-ng.htm"> SX Specific Pulse Width Measurement </A> |
Did you find what you needed? |
Welcome to massmind.org! |
Welcome to massmind.org! |
.