please dont rip this site

Scenix Spi_ml.src

;=======================================================================
;=======================================================================
;	SERIAL PERIPHERAL INTERFACE (SPI) DRIVER
;	SPI_ML
;	Revision 1.01, 07.05.98
;	Developed by Authentic Engineering for Scenix Semiconductor, Inc.
;	Authentic Engineering // http://www.authenticeng.com // ak@silcom.com
;	
;=======================================================================
;	MASTER MODE LOW RATE SPI DRIVER. SINGLE MASTER CONFIGURATION
;
;	This driver provides  SPI interface to realtively slow devices.
;	The data are transfered by words. Word length is software configurable 
;	from 1 to 16 bits. 
;	This driver is a part of a set of SX SPI drivers. It makes use of general
;	set of control and status data, developed for the entire family of drivers
;
;		CLOCK RATE
;
;	The SPI clock rate is driven by the system RTCC. 
;	Minimum clock rate is limited by the RTCC prescaler setting which should be 
;	configured by the user. When the RTCC is configured to the minimum rate and
;	prescaler is set to 1:2, the SPI clock rate will be equal to 10.2 microsec.
;	With the prescaler setting at 1:256 the minimum clock rate will be 1.3056 millisec.
;	Maximum clock rate can be achived at RTCC prescaler setting 1:2 
;	and  RTCC reload register - $80. Desierable configuration of the RTCC prescaler 
;	must be determined by the user.
;
;	Clock (SCLK) PHASE and POLARITY are software configurable.
;
;	There are FOUR basic signal lines associated with the SPI protocol:
;		Master-Out-Slave-In		MOSI signal line
;		Master-In-Slave_Out		MISO signal line
;		Serial Clock			SCLK signal line
;		Slave Select			SS signal line
;	Arbitrary pins of the SX-28 can be used for current driver
;
;==============================================================================
;
;		INITIALIZATION OF SPI DRIVER
;
;	USER program must:
;	1. Provide appropriate configuration of the SX-28 ports.
;
;	2. Define next parameters:
;
;	SPI_RAM_BANK	- to define the origin in SX  RAM banks 
;	SPI_CLOCK_RATE	- to define the clock rate. This byte is used by the driver 
;			  as the RTCC reload register value	
;	SPI_COMMAND	- command and configuration byte. This byte defines:
;			- SPI Clock polarity
;			- Mode (Master or Slave)
;			- Speed (Fast or Slow)
;			- Direction (Read/Write)
;			- Word Lenght (1 to 16).
;	Driver will set the RTCC reload value to the SPI_CLOCK_RATE. The USER
;	program must take care about restoration of the RTCC reload value, after
;	the SPI driver will complete its operation.
;
;	Current driver support only Master Mode and Slow Speed data transfer.
;
;	The driver supports 5 commands, specified by the 4 MSBs of the SPI_COMMAND byte
;			$0	RESET 
;			$2	GET WORD in MASTER mode, define FALLING edge
;			$6	GET WORD in MASTER mode, define RISING edge
;			$A	SEND WORD in MASTER mode, define FALLING edge
;			$E	SEND WORD in MASTER mode, define RISING edge
;	Generally for the SPI interface there is no diffrence between GET and SEND,
;	however it seems convinient to have different commands, because it allows to customize
;	transmit and receive cycles for specific peripherals. Such an examle is presented in Demo #1. 
;
;	Four LSBs of SPI_COMMAND byte are used for word length definition.
;	
;			$1	corresponds to one bit length
;			...
;			$F	corresponds to fifteen bit legth
;			$0	corresponds to sixteen bit length
;
;	For example, SPI_COMMAND for 12 bit data transfer to the peripheral looks like - $EC
;
;	3. Driver is driven by RTCC interrupts. In order to start data transfer USER program
;	must:
;		- check that SPI_BUSY flag is cleared 
;		- set SPI_CLOCK_RATE and SPI_COMMAND
;		- enable timer interrupts
;		- perform JMP SPI_ENTRY when RTCC interrupt occures
;	See example in DEMO #1
;=============================================================================================
;
;	The SPI_STATUS byte provides the information on driver status. It consists of a set of
;	flags, described in the comments to the code.
;
;
;	SX-28 pin assignment presented below is an example used in 'SPI DEMO #1'
;	program.
;=======================	CODE START

			device	pins28, pages4,banks8
			device	turbo, stackx, optionx 
			id	'SPI_ML'

;=======================	PIN ASSIGNMENT
;========	example of pin assignment used in DEMO #1

spi_clk_pin		=	rb.0	;SPI clock line
spi_out_pin		=	rb.1	;master_in slave_out line
spi_in_pin		=	rb.2	;master_out slave_in line 
spi_ADC_cs_pin		=	rb.4	;slave select (ADC)
spi_DAC_cs_pin		=	rb.5	;slave select (DAC)

;========================	SPI DEVICE RAM ORIGIN

			org	10h	;example of RAM bank assignment
spi_ram_bank		=	$

spi_command		ds	1

bit_wide_0		equ	spi_command.0	;the word length LSB
bit_wide_1		equ	spi_command.1	;1_st bit	
bit_wide_2		equ	spi_command.2	;2_nd bit	
bit_wide_3		equ	spi_command.3	;the word length MSB 
fast_ON			equ	spi_command.4	;set if FAST MODE
master_ON		equ	spi_command.5	;set if MASTER MODE
rising_ON		equ	spi_command.6	;set if RISING EDGE
transmit_ON		equ	spi_command.7	;set if TRANSMIT

;=======================	SPI_STATUS byte
spi_status		ds	1
spi_ready		equ	spi_status.0	;SET when driver is ready (has been initialized)

spi_busy		equ	spi_status.1	;set when data transfer is active
;spi_master		equ	spi_status.2	;SET when SPI master is inited
;spi_slave		equ	spi_status.3	;SET when SPI slave is inited 

spi_command_ERR		equ	spi_status.4	;set when command byte containes not supported command 
spi_tx_complete		equ	spi_status.5	;transmit complete
spi_rx_complete		equ	spi_status.6	;receive complete
;spi_error		equ	spi_status.7	;SET when transmit is not finished correctly

;spi_rx_complete and spi_tx_complete flags are needed when two different SS lines were inited simultaneously
;and receive and transmit are controled in the same time. Otherwise, this flag is not extended 
;(see SPI_M, SPI_S SPI drivers).

;=======================	SPI_STATE byte
spi_state		ds	1

spi_ms_ON		equ	spi_state.0	;set when Master Mode
spi_sl_ON		equ	spi_state.1	;set when Slave Mode
spi_rx_ON		equ	spi_state.2	;set when Receive Mode
spi_tx_ON		equ	spi_state.3	;set when Transmit Mode
spi_clk_state		equ	spi_state.4	;state of the SPI_CLOCK line;
;spi_timer_IRQ_ON	equ	spi_state.5	;SPI transfer under timer IRQ	:indicated by rc.0
;spi_port_IRQ_ON	equ	spi_state.6	;SPI transfer under port IRQ	:indicated by rc.2

;=======================	SPI_CLOCK byte

spi_clk_rate		ds	1		;RTCC reload value

spi_buff		ds	1		;SPI I/O shift register (MSByte)
spi_buff_low		ds	1		;SPI I/O shift register (LSByte)
spi_shift_counter	ds	1		;shift counter

spi_bits_total		ds	1		;number of bits to transfer
spi_shifts_init		ds	1		;number of initial shifts before transfer

spi_clk_counter		ds	1		;used only for DEMO #1 with LTC1594 
spi_clks_init		ds	1		;used only for DEMO #1 with LTC1594

;=======================	INTERRUPT START

spi_entry	bank	spi_ram_bank		;SPI driver entry point
		jb	master_ON,master_entry	

		snb	rising_ON
		setb	spi_command_ERR		;return from interrupt if wrong command
		snb	transmit_ON
		setb	spi_command_ERR		
	
		clr	spi_command
		setb	spi_ready

		mov	w,spi_clk_rate		
		retiw				

;=======================	SPI MASTER ENTRY

master_entry		test	spi_shift_counter	;test if this is first entry
			jnz	:master_start		

:init_master		jb	spi_ms_ON,:ms_rx_finish	;initialization of the driver (on the first entry)
			
			setb	spi_busy_ON
			setb	spi_ms_ON			
			
			sb	transmit_ON
			setb	spi_rx_ON
			snb	transmit_ON
			setb	spi_tx_ON
			snb	spi_rx_ON
			clrb	spi_ADC_cs_pin		;this is an example to show how
							;generate CS signals for a specific 
							;peripherals. This is CS for ADC
			snb	spi_tx_ON
			clrb	spi_DAC_cs_pin		;CS for DAC

			sb	rising_ON		;set the SPI_CLK polarity
			clrb	clk_state
			snb	rising_ON
			setb	clk_state
			sb	rising_ON
			clrb	spi_clk_pin
			snb	rising_ON
			setb	spi_clk_pin

			mov	w,spi_command		;set the number of bits to transfer
			and	w,#%00001111
			mov	spi_bits_total,w
			mov	w,spi_command
			or	w,#%11110000
			mov	spi_shifts_init,w
			not	spi_shifts_init
			inc	spi_shifts_init
			mov	spi_shift_counter,spi_bits_total
			clc	
			rl	spi_shift_counter

			mov	spi_clk_counter,spi_clks_init	;Example for LTC1594 ADC only
			clc					;LTC1594 input MX control	
			rl	spi_clk_counter			;end of LTC1594 part

:set_bit_position	test	spi_shifts_init		;initial shift before transfer
			clc				;needed to put MSB of the word to
			sz				;bit.7 SPI_BUFF position
			rl	spi_buff_low
			sz
			rl	spi_buff
			sz
			djnz	spi_shifts_init,:set_bit_position

			jmp	:master_exit		;initialization done, first interrupt exit

;===============================================	Example of the LTC1594 driver
:master_start		nop
			test	spi_clk_counter		;Example for LTC1594 ADC only
			jz	:master_rx		;Jump to normal master receive
			xor	rb,#%00000001		;LTC1594 input MX control
			dec	spi_clk_counter		;sclk ADC UP/DOWN

			jmp	:master_exit		;interrupt exit for the ADC MX control

;===============================================	End of ltc1594 example

:master_rx		jb	clk_state,:master_tx	;bit reception from SPI_IN_PIN
			movb	c,spi_in_pin
			rl	spi_buff_low
			rl	spi_buff
			setb	spi_clk_pin	
			dec	spi_shift_counter
			setb	clk_state	
			jmp	:master_exit		;bit received

:master_tx		movb	spi_out_pin,spi_buff.7	;bit transmit
			clrb	spi_clk_pin
			dec	spi_shift_counter
			clrb	clk_state	
			jmp	:master_exit		;bit transmitted

:ms_rx_finish		sb	spi_rx_ON		;reception completed
			jmp	:ms_tx_finish		
			setb	spi_rx_complete		;correct reception finished
			setb	spi_ADC_cs_pin		;disable ADC CS 
			clrb	spi_rx_ON
			jmp	:master_finish

:ms_tx_finish		setb	spi_DAC_cs_pin		;disable DAC CS
			clrb	spi_tx_ON		;transmission completed
			setb	spi_tx_complete
			jmp	:master_finish

:master_finish		clrb	spi_ms_ON
			clr	spi_command
			clrb	spi_busy_ON

:master_exit		mov	w,spi_clk_rate
			retiw

;=======================	END OF MASTER MODE SLOW SPI DRIVER

file: /Techref/scenix/spi_ml.src, 9KB, , updated: 1999/2/20 12:23, local time: 2024/12/2 12:48,
TOP NEW HELP FIND: 
18.97.9.168:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://massmind.org/techref/scenix/spi_ml.src"> scenix spi_ml</A>

Did you find what you needed?

 

Welcome to massmind.org!

 

Welcome to massmind.org!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .