Scenix DEMO3M.SRC

;=======================================================================
;=======================================================================
;	SERIAL PERIPHERAL INTERFACE (SPI) VIRTUAL PERIPHERALS
;	DEMO3M.SRC -- Demo #3 Master SX Software
;	SPIM (Authentic SPI Master) Virtual Peripheral Demo Program
;	Revision 1.02, 07.21.98
;	Developed by Authentic Engineering for Scenix Semiconductor, Inc.
;	Authentic Engineering // http://www.authenticeng.com // ak@silcom.com
;=======================================================================
;
;
;	DEMO#3 provides an example of data transfer between two 
;       SX microcontrollers through the SPI data bus. 
;	DEMO#3 consists of two programs - DEMO3M.SRC and DEMO3S.SRC, 
;	which correspond to the SPI Master and SPI Slave sides accordingly.
;       The are 4 signal lines that connect the Master to the Slave:
;
;		Master-Out-Slave-In		MOSI signal line
;		Master-In-Slave_Out		MISO signal line
;		Serial Clock			SCLK signal line
;		Slave Select			SS signal line
;
;	The Slave Select (SS) Line from Master to Slave signals the 
;	latter to start sending/receiving data. The word length is set 
;	to 16 bits in this demo (VP permits 1 to 16 bits). 
;
;	Authentic SPI virtual perphirals perform shifting in and out at 
;	the same time, as most hardware SPI implemetations do. 
;
;	The demo works as follows:
;       - Assuming that Slave has been initialized prior to Master,
;	  the Master sends The Predefined Word 256 times.
;       - The Slave SX is configured to perform the loopback function, 
;	  that is, every time Slave sends to the Master whatever it has 
;	  received from the Master during the previous transmission.
;       - After the initial 256 transmissions Master switches into 
;	  the loopback mode.
;	- The data transfer of The Predefined Word can be easily observed 
;         with the help of oscilloscope. 
;
;	SPI clock period for this demo is 900 nsec - maximum clock 
;	rate supported	by the SPIS (SPI Slave VP).
;	
;	Data transfer from Master side is triggered by RTCC interrupt with
;	a period of 25.6 microseconds.
;
;=======================================================================
;
;	
;	Authentic SPIM (SPI Master) Virtual Peripheral
;
;	SPIM is a part of the Authetic SPI virtual peripherals for SX micro.
;	This VP provides simple and efficient way to send/get one word of 
;	data to/from SPI compatible Slave device.
;	
;	SPIM Clock rate can be selected starting from 1.72 MHz (max). 
;	Corresponding minimum clock period is 580 ns. Clock period can be
;	incremented with 160 nsec increment. It is possible to achive faster
;	data transfer rates sacrifising the rate programmability. Maximum 
;	clock rate of 2.5MHz can be achived by removing part of the program, 
;	responsible for programmable clock rate. Minimum clock rate is
;	prctically unlimited, however, for clock rates lower than 500KHz
;	we recommend to use Authentic SPIML (low rate SPI Master VP).
;	
;	Word length can be set to anywhere from 1 to 16 bits. Longer word 
;	lengths could be easily implemented if needed.
;
;	Clock polarity is configurable by using the appropriate command byte.
;
;	Four I/O signal lines are associated with any SPI communication:
;		
;		Master-Out-Slave-In		MOSI signal line
;		Master-In-Slave_Out		MISO signal line
;		Serial Clock			SCLK signal line
;		Slave Select			SS signal line
; 
;	SPIM does not make any diffenece between read and write cycles.
;	The data is clocked in and out simultaneously. 
;
;	If necessary, user may want to add more sophistication to the data 
;	transfer by adding Read/Write and handshaking signals. All that 
;	can be easily implemented without affecting the core SPIM program.
;
;	SPIM controlls MOSI; MISO; SCLK lines. User program must provide 
;	appropriate control for SS lines.
;
;	Arbitrary pins of the SX-28/SX-18 can be assigned for SPIM.
;	
;	To initialize SPIM user must: disable the interrupts; initilize
;	SX I/O ports (calling SPIM_INIT); place	the outgoing data into 
;	the I/O buffer, set SS signal and call SPIM_EXECUTE. Since SPIM 
;	is not using any interrupts, it will transfer the data and return 
;	control to user program.
;	
;	The two-byte (16 bits) send/receive buffer is allocated in 
;	memory as SPIM_LSB and SPIM_MSB. Data are shifted starting 
;	from the most significant bit. 
;	In case of less than 16-bit long data word, the SPIM will 
;	automatically align the MSBit of the word to the MSBit of 
;	the buffer before shifting. No user intervention is required. 
;	The contents of SPIM_LSB and SPIM_MSB are not preserved 
;	during the driver operation since the bits are always shifted in.
;
;	-- SPIM control, status and I/O DATA registers --
;	
;	SPIM_RATE. This byte defines the clock rate. When set to 1 it 
;	defines	maximum clock rate of 1.72 MHz (580 nsec period). 
;	The actual clock period can be calculated as 420 nsec plus
;	160 nsec, multiplied by the SPIM_RATE. SPIM_RATE equal to
;	zero will define maximun clock period of 41.380 usec.
;
;	SPIM_PORT must be defined by user to point to the SX Port 
;	- A,B or C, which will generate SPI Clock signal. 
;	For instance: spim_port 	=	rb.
;
;	SPIM_PORTA_MASK, SPIM_PORTB_MASK, SPIM_PORTC_MASK. These
;	bytes are the images of SX I/O ports direction registers.
;	They are written to corresponding ports direction registers
;	during the initialisation of SPIM.
; 
;	SPIM_CLK_MASK defines the SPI Clock pin. The pin is defined by
;	setting corresponding bit of SPIM_CLK_MASK.
;	For instance:
;	spim_portc_mask	=	$fd
;	spim_port	=	rc
;	spim_clk_mask	=	$02
;	will define rc.1 as SPI Clock pin.
;	
;	SPIM_CMD - command and configuration byte. This byte defines:
;			- SPI Clock polarity
;			- direction (Read/Write)
;			- number of bits to send/receive
;
;	SPIM supports 4 commands, specified by the 4 MSBits of the 
;	SPIM_CMD byte
;
;		$3	- GET WORD in MASTER FAST mode, define FALLING edge;
;		$7	- GET WORD in MASTER FAST mode, define RISING edge;
;		$B	- SEND WORD in MASTER FAST mode, define FALLING edge;
;		$F	- SEND WORD in MASTER FAST mode, define RISING edge.
;
;	Practically there is no difference between the GET and SEND commands. 
;	When the I/O buffer is shifted out, the input data is always 
;	shifted in. The different commands are provided for user convinience 
;	and confusion. The contents of SPIM_LSB and SPIM_MSB are 
;	not preserved during the driver operation since the bits are 
;	always shifted in even if they don't make any sense.
;
;	Four LSBits of the command byte define the word length. 
;	$00 sets the length to 16 bits
;	$01 sets the length to 1 bit 
;	 ...
;	$0F sets the length to 15 bits
;
;	The SPIM_CMD byte also serves as a ready flag. SPIM will clear this 
;	byte upon the success of data transfer.
;
;	SPIM_STATUS byte provides the error status information to the user
;	program. It has 1 error flag:
;	 bit 4 - set to 1 when the SPIS_CMD byte contains an unsupported command 
;
;	-- SPIS ENTRY POINTS --
;
;	SPIM_INIT - Initialization subroutine. It provides appropriate configuration
;	for SX I/O ports ports
;	
;	SPIM_EXECUTE - This is the actual VP entry point which may be
;	called either from the interrupt service routine or from MAIN program.
;
;	SPIM_SS_SET - user defined subroutine to set active level on SS pin.
;	SPIM_SS_RESET - user defined subroutine to set passive level on SS pin.
;	In the case of multiple devices on SPI bus, user must provide appropriate
;	control over SS signals.
;
;	SPIM_ORG. This is the base address of SPIM VP. Typically it will be
;	next ROM location, after the user program.  
;
;	-- How to use SPIM from the user program --
;
;	1. Make sure that no interrupt is allowed during execution of SPIM.
;   
;	2. Verify that the execution parameters are configured properly:
;		SPIM_RATE 
;		SPIM_PORT_A_MASK
;		SPIM_PORT_B_MASK
;		SPIM_PORT_C_MASK
;		SPIM_PORT
;		SPIM_CLK_MASK
;		SPIM_CMD
;
;	3. Configure I/O ports by calling SPIM_INIT.
;
;	4. Verify that SPIM is ready for execution by testing the SPIM_CMD byte.
;
;	5. Place the outgoing data into SPIM_LSB and SPIM_MSB 
;
;	6. Call SPIM_EXECUTE from the interrupt.
;	
;	7. Test SPIM_CMD for completion and SPIM_STATUS for errors. 
;          Unload the data from SPIM_LSB and SPIM_MSB
;	
;	Your SPIM is now ready for reuse. Repeat from step 4.
;
;=======================================================================
									
	
;**************************** CODE START *******************************

			device	pins28, pages4,banks8,oschs	;This is the SX-28 device configuration 
			device	turbo, stackx, optionx 		;data which should be used to run this VP
			id	'DEMO3M'

reset				reset_entry

;***************************** I/O PINS ********************************

spim_port			=	rb	;SPI port for clock pin

spim_clk_pin			=	rb.0	;SPI clock line
spim_out_pin			=	rb.1	;master_in slave_out line
spim_in_pin			=	rb.2	;master_out slave_in line 
spim_MCU_cs_pin			=	rb.3	;slave select/slave request micro

;******************************* RAM ***********************************
;SPIS DEMO#3 Variables. 
				org	8
sys_timer_rate			ds	1		;RTCC reload value for MAIN program			
spim_init_cycles		ds	1		;numder of initial cycles when SPIM
							;sends to Slave prederfined SPI_DEMO_DATA
spim_init_counter		ds	1		;counter of initial cycles
spim_demo_rate			ds	1		;SPIM_RATE for DEMO#3

spim_demo_data_MSB		ds	1		;predefined data for SPI transfer to Slave		
spim_demo_data_LSB		ds	1

spim_demo_cmd			ds	1		;SPIM_CMD for DEMO#3
	
;************************* INTERRUPT HANDLER ***************************
;Calls the SPIM VP on every RTCC interrupt

			org	0
			call	spim_execute
			mov	w,sys_timer_rate
			retiw	
									
;************************ DEMO#3 SUBROUTINES ****************************
;user defined subroutines to generate SPI SS signal
spim_SS_set		clrb	spim_MCU_cs_pin		;set MCU__SS active (low)
			ret

spim_SS_reset		setb	spim_MCU_cs_pin		;set MCU__SS passive (high)
			ret

;************************ DEMO#3 MAIN PROGRAM **************************

reset_entry		clr	fsr			;clear RAM  
:loop			setb	fsr.4		
			clr	ind	
			ijnz	fsr,:loop	

			bank	spim_ram_bank		;SPI_bank initialization

;Set configuration bytes for PortB and SPI Clock line
			mov	spim_clk_mask,#$01	;SPI Clock line mask for SPI Port	
			mov	spim_portb_mask,#$04	;PortB data direction byte  

;Set DEMO#3 control data
			mov	sys_timer_rate,#-80	;set system timer to 25.6 usec
			mov	spim_init_cycles,#$ff	;set number of initial cycles to 255

;set SPIM control data
			mov	spim_demo_rate,#$03	;set SPI Clock period 900 nsec	
			mov	spim_demo_data_MSB,#$0d	;define the data to transfer		
			mov	spim_demo_data_LSB,#$35		

			mov	spim_demo_cmd,#$f0	;Set SPIM_CMD to SEND RISING 16 BIT
;			mov	spim_demo_cmd,#$bc	;Set SPIM_CMD to SEND FALLING 12 BIT

;initialise SPIM
			mov	spim_rate,spim_demo_rate	;set SPI Clock rate to 900 nsec
			call	spim_init		;configure SPIM ports
			mov	!option,#$03			;enable RTCC interrupt
								;set RTCC prescaler rate 1:16

;start data transfer, SPIM will be called from RTCC interrupt handler on every RTCC interrupt		 		
;initial 255 cycles when spim_demo_data are sent to Slave

			mov	spim_init_counter,spim_init_cycles	;spim_init_counter to $ff
:spim_transfer_start	test	spim_cmd			;wait for SPIM to be ready 
			jnz	:spim_transfer_start		;for next transfer

			mov	spim_msb,spim_demo_data_MSB	;initialize I/O buffer
			mov	spim_lsb,spim_demo_data_LSB
			mov	spim_cmd,spim_demo_cmd		;initialize SPIS_CMD 
														
			djnz	spim_init_counter,:spim_transfer_start

;initial 255 cycles finished
		
main_master		call	:spim_transfer		;main loop 
			jmp	main_master

:spim_transfer		test	spim_cmd		;SPIM VP access loop		
			jnz	:spim_transfer
			mov	spim_cmd,spim_demo_cmd			
			ret

spim_org		equ	$
									
;***********************************************************************
;************************** Authentic SPI MASTER VP ********************

			org	10h
spim_ram_bank		=	$

;SPIM control data

spim_cmd		ds	1		;SPIM command byte

fast_ON			equ	spim_cmd.4	;set to 1 for SPIM mode is used

master_ON		equ	spim_cmd.5	;set to 1 if MASTER
rising_ON		equ	spim_cmd.6	;set to 1 if RISING
transmit_ON		equ	spim_cmd.7	;set to 1 if TRANSMIT

spim_clk_mask		ds	1		;defines SPI Clock pin
spim_porta_mask	ds	1			;PortA direction register image
spim_portb_mask	ds	1			;PortB direction register image
spim_portc_mask	ds	1			;PortC direction register image

;SPIM status data

spim_status		ds	1		;SPIM status byte

spim_cmd_error		equ	spim_status.4	;error - unsupported comand
	
;SPIS I/O buffer

spim_msb		ds	1		;I/O data buffer
spim_lsb		ds	1

;SPIS private data

spim_shift_counter	ds	1		;I/O shift counter

spim_bits_total		ds	1		;number of bits to transfer
spim_shifts_init	ds	1		;number of bits for initial shift
	
spim_rate		ds	1		;clock rate factor
spim_rate_counter	ds	1		;clock rate delay counter

			org	spim_org

;********************* SPIM INITIALIZATION ROUTINE *********************

spim_init		mov	m,#$0f			;set up data direction registers
			mov	!rb,spim_portb_mask	;configure ports
			mov	!ra,spim_porta_mask
			mov	!rc,spim_portc_mask
			ret
									
;************************* SPIM DATA TRANSFER **************************

spim_execute		bank	spim_ram_bank		;set SPIM RAM bank
			snb	master_ON
			jb	fast_ON,spim_cmd_proc	;begin decoding SPIM_CMD
			setb	spim_cmd_error		;unsupported command
	
spim_exit		clr	spim_cmd		;SPIM exit
			ret
;decode SPIM_CMD 
spim_cmd_proc	
			sb	rising_ON		;set the SPI_CLK polarity
			clrb	spim_clk_pin
			snb	rising_ON
			setb	spim_clk_pin

			mov	w,spim_cmd		;set number of bits to transfer	
			and	w,#$0f			;decode four LSBits of SPIM_CMD
			mov	spim_bits_total,w	
			test	spim_bits_total
			snz
			mov	spim_bits_total,#$10

			mov	spim_shift_counter,spim_bits_total	;set shift bit counter
			mov	spim_shifts_init,#$10
			sub	spim_shifts_init,spim_bits_total	;set initial shifts counter

			call	spim_SS_set		;activate user defined SS lines

			test	spim_shifts_init	;initial shift needed? 
			jz	:spim

;prepare data for transfer
:set_bit_position	clc				;initial shift for the data < 16 bit long
			rl	spim_lsb
			rl	spim_msb
			djnz	spim_shifts_init,:set_bit_position

;data transfer
:spim			test	spim_shift_counter	
			jz	:spim_execute_exit
;shift bit out
			mov	spim_rate_counter,spim_rate	;define transfer rate
			djnz	spim_rate_counter,$		;in shift data out cycle

			movb	spim_out_pin,spim_msb.7		;shift data out
			xor	spim_port,spim_clk_mask		;change SPI Clock state
			dec	spim_shift_counter	
			rl	spim_lsb
			rl	spim_msb
;shift bit in
			mov	spim_rate_counter,spim_rate	;define transfer rate
			djnz	spim_rate_counter,$		;in shift data in cycle

			movb	spim_lsb,spim_in_pin		;shift bit in
			xor	spim_port,spim_clk_mask		;change SPI clock state
			jmp	:spim

:spim_execute_exit	call	spim_SS_reset			;disable SS
			jmp	spim_exit			;exit
	
			ret					;TO CLOSE THE LABEL SCOPE
									
;***************************** END OF SPIM VP **************************

  .